This map shows modeled outdoor noise across Alchesay Flat at 100-meter resolution, combining road, aviation, and rail sources. Green areas measure below 45 dBA. Orange and red exceed the EPA's 55 dBA outdoor threshold linked to long-term health effects. Use the layer toggles to view each source on its own or all together.
What the numbers sound like
- 30 dBAWhisper
- 40 dBASoft rainfall
- 45 dBAQuiet suburban street at night
- 50 dBAQuiet office
- 55 dBAEPA outdoor threshold: light traffic 100 ft away
- 60 dBANormal conversation an arm's length away
- 65 dBABusy restaurant
- 70 dBAHighway traffic 50 ft away
- 80 dBACity bus interior
Population Above the EPA Outdoor Threshold
The EPA's 55 dBA outdoor reference level is a common benchmark for residential noise exposure, especially for activity interference, annoyance, and long-term community noise concerns. About 4 Alchesay Flat residents, or 1.6%, live above that level. By land area, 10.2% of Alchesay Flat is above 55 dBA.
See how noise in Alchesay Flat compares to similar-sized cities.
Noise by Part of Alchesay Flat
Average noise levels for Alchesay Flat residents, grouped by direction from the center of Alchesay Flat. Northern Alchesay Flat carries the highest population-weighted average; Southern Alchesay Flat carries the lowest. Just 0% of residents in Southern Alchesay Flat live in blocks above the EPA's 55 dBA threshold, a third of the share in Northern Alchesay Flat.
Northern Alchesay Flat
1% of people above 55 dBA
Southern Alchesay Flat
0% of people above 55 dBA
Western Alchesay Flat
3% of people above 55 dBA
Northern Alchesay Flat sounds about 55% louder than Southern Alchesay Flat to the human ear, a 6.3 dBA gap. Every 10 dBA roughly doubles perceived loudness. Within any of these directions, two homes a quarter mile apart can still differ by 10 or more dBA depending on how close they sit to a major highway.
Loudest Road Corridors
The model evaluates every road in Alchesay Flat using federal traffic counts, posted speeds, heavy-truck ratios, and pavement type. The source level shown is the modeled noise at the road centerline, where it is loudest. Noise drops with distance, faster in vegetated areas and slower over open pavement.
How far back from ~~s~087~~~~~~~~~~~~~~~~~~~~~~~~~ do you need to be?
~~s~087~~~~~~~~~~~~~~~~~~~~~~~~~ produces an estimated 72 dBA at its loudest centerline points. Noise drops logarithmically with distance, with the exact rate depending on what's between you and the road. Tree cover, walls, terrain, and pavement type all matter. At roughly a quarter mile back, traffic fades into the noise level of a soft rainfall.
Calculated from the model's calibrated attenuation formula. About 0% of Alchesay Flat sits under tree canopy (much lighter than most cities) and roughly 0% is impervious surface like pavement and rooftops. Both are folded into the per-place decay rate above. Heavier canopy pulls noise down faster with distance; impervious surfaces slow the drop.
Airport Noise
Phoenix Sky Harbor International (PHX) sits southwest of Alchesay Flat. The U.S. Department of Transportation measures aviation noise around this airport directly, and the model uses those federal measurements rather than synthetic predictions.
Blocks under the approach and departure paths carry combined road-plus-aviation noise, with some exceeding 75 dBA on the map's Overall layer. Blocks on the opposite side of Alchesay Flat, particularly to the northeast, show no measurable aviation contribution. Use the Aviation toggle on the map above to isolate the airport's footprint.
How Noise Is Distributed Across Alchesay Flat
The bar chart below shows the share of Alchesay Flat residents in each noise band. About 100% of residents live below the EPA's 55 dBA threshold, and roughly 0% live in blocks above 60 dBA. Long-term exposure in that range is linked to elevated stress hormones and cardiovascular risk.
How Alchesay Flat Compares
Alchesay Flat sits at the quieter end of the spectrum. Below: how Alchesay Flat's average outdoor noise and share of residents above the EPA threshold compare with Goldfield, Jakes Corner, Wet Camp Village, and Chandler Heights.
Average noise level (dBA)
Alchesay Flat's 41.6 dBA pop-weighted average is at the quieter end of the spectrum. Arizona as a whole averages 53.0 dBA and the U.S. averages 52.0 dBA. Both are lower than Alchesay Flat because most of either area is rural land away from major roads.
Share of residents above 55 dBA
About 1.6% of Alchesay Flat residents live in blocks where outdoor levels exceed the EPA's 55 dBA threshold. That's in the middle of its peer group. Measured by land area instead, 10.2% of Alchesay Flat's footprint sits above 55 dBA, against a Arizona average of 28.3% and a national average of 28.1%.
What This Means if You're Moving to Alchesay Flat
- Distance from highways matters more than the neighborhood name. Two homes in the same zip code can differ by 20 dBA if one sits 100 meters from ~~s~087~~~~~~~~~~~~~~~~~~~~~~~~~ and the other 500 meters away. The model captures this at 100-meter resolution, so noise exposure changes block by block.
- Tree canopy can help reduce modeled noise exposure. Roughly 0% of Alchesay Flat is under tree cover (much lighter than most cities), and the dominant land cover is shrub / scrub. Both are measured from federal USDA Forest Service and USGS satellite imagery at 30-meter resolution. Streets with 60% or higher canopy show 3 to 5 dBA lower noise than comparable streets with bare ground or pavement, which is why the per-place decay rate above already accounts for it.
- Airport noise is directional. Phoenix Sky Harbor International's approach paths concentrate aviation noise to the southwest. Neighborhoods to the northeast of downtown show no measurable contribution from the airport.
Sources & Methodology
The BestNeighborhood noise model is calibrated against nearly one million federal ground-truth measurements across four states. Road noise is computed from segment-level federal traffic data and propagated outward using physics-based acoustic decay, with attenuation rates that depend on the surrounding land cover.
Federal datasets used:
FHWA Highway Performance Monitoring System: road geometry, traffic counts, lane configuration
U.S. DoT Bureau of Transportation Statistics National Transportation Noise Map: aviation and rail noise, road calibration ground truth
USGS / MRLC National Land Cover Database: land cover and impervious surface coverage
USDA Forest Service Tree Canopy Cover: vegetation density for sound propagation
U.S. Census Bureau TIGER/Line: block-level geography and population
U.S. EPA Levels Document: 55 dBA outdoor reference level
All inputs are published federal datasets. Block-level noise is computed by combining road, rail, and aviation sound sources in the energy domain, the same physics used in professional environmental noise assessments. Read the full methodology.