Noise Levels in Arthur City, TX | Find Quiet Neighborhoods With Our Sound Map
41 dBA
Average noise across Arthur City
Quiet suburban street at night
32
Residents above the EPA 55 dBA threshold
3% of Arthur City residents
67 dBA
Loudest residential point
Highway traffic 50 ft away
This map shows modeled outdoor noise across Arthur City at 100-meter resolution, combining road, aviation, and rail sources. Green areas measure below 45 dBA. Orange and red exceed the EPA's 55 dBA outdoor threshold linked to long-term health effects. Use the layer toggles to view each source on its own or all together.
Overall
Road
Rail
Aviation
Click the map to explore
35 dBa55 dBa (EPA limit)90+ dBa
3545557090
Quietest (dBA)Loudest
Colorblind friendlyoff
What the numbers sound like
30 dBAWhisper
40 dBASoft rainfall
45 dBAQuiet suburban street at night
50 dBAQuiet office
55 dBAEPA outdoor threshold: light traffic 100 ft away
60 dBANormal conversation an arm's length away
65 dBABusy restaurant
70 dBAHighway traffic 50 ft away
80 dBACity bus interior
Population Above the EPA Outdoor Threshold
The EPA's 55 dBA outdoor reference level is a common benchmark for residential noise exposure, especially for activity interference, annoyance, and long-term community noise concerns. About 32 Arthur City residents, or 2.9%, live above that level. By land area, 6.8% of Arthur City is above 55 dBA.
Average noise levels for Arthur City residents, grouped by direction from the center of Arthur City. Central Arthur City carries the highest population-weighted average; Eastern Arthur City carries the lowest. Just 4% of residents in Eastern Arthur City live in blocks above the EPA's 55 dBA threshold, a fifth of the share in Central Arthur City.
Central Arthur City
53.0 dBA · Moderate-loud
Quiet office to normal conversation
29% of people above 55 dBA
QuietLoud
Eastern Arthur City
39.2 dBA · Quiet
Soft rainfall
4% of people above 55 dBA
QuietLoud
Northern Arthur City
44.2 dBA · Quiet
Quiet suburban street at night
2% of people above 55 dBA
QuietLoud
Western Arthur City
40.7 dBA · Quiet
Soft rainfall
0% of people above 55 dBA
QuietLoud
Central Arthur City sounds about 160% louder than Eastern Arthur City to the human ear, a 13.8 dBA gap. Every 10 dBA roughly doubles perceived loudness. Within any of these directions, two homes a quarter mile apart can still differ by 10 or more dBA depending on how close they sit to a major highway.
How far back from US Hwy 271 do you need to be?
US Hwy 271 produces an estimated 66 dBA at its loudest centerline points. Noise drops logarithmically with distance, with the exact rate depending on what's between you and the road. Tree cover, walls, terrain, and pavement type all matter. At roughly a quarter mile back, traffic fades into the noise level of a soft rainfall.
At source
66 dBA
Busy restaurant
165 ft
53 dBA
Quiet office to normal conversation
330 ft
46 dBA
Quiet office
660 ft
39 dBA
Soft rainfall
¼ mile
35 dBA
Soft rainfall
½ mile
35 dBA
Soft rainfall
Calculated from the model's calibrated attenuation formula. About 32% of Arthur City sits under tree canopy (about average for cities) and roughly 0% is impervious surface like pavement and rooftops. Both are folded into the per-place decay rate above. Heavier canopy pulls noise down faster with distance; impervious surfaces slow the drop.
-->
Rail Noise
Active freight rail runs through parts of Arthur City. For most blocks the rail-only contribution is small. Combined road-plus-rail noise rarely exceeds road noise on its own. The exceptions are the handful of blocks within roughly a quarter mile of the right-of-way during pass-through hours.
Use the Rail toggle on the map above to isolate rail's contribution from road and aviation.
How Noise Is Distributed Across Arthur City
The bar chart below shows the share of Arthur City residents in each noise band. About 98% of residents live below the EPA's 55 dBA threshold, and roughly 2% live in blocks above 60 dBA. Long-term exposure in that range is linked to elevated stress hormones and cardiovascular risk.
How Arthur City Compares
Arthur City sits at the quieter end of the spectrum. Below: how Arthur City's average outdoor noise and share of residents above the EPA threshold compare with Cavines, Blossom, Faulkner, and Sumner.
Average noise level (dBA)
Arthur City's 41.1 dBA pop-weighted average is at the quieter end of the spectrum. Texas as a whole averages 50.8 dBA and the U.S. averages 52.0 dBA. Both are lower than Arthur City because most of either area is rural land away from major roads.
Share of residents above 55 dBA
About 2.9% of Arthur City residents live in blocks where outdoor levels exceed the EPA's 55 dBA threshold. That's in the middle of its peer group. Measured by land area instead, 6.8% of Arthur City's footprint sits above 55 dBA, against a Texas average of 22.8% and a national average of 28.1%.
What This Means if You're Moving to Arthur City
Distance from highways matters more than the neighborhood name. Two homes in the same zip code can differ by 20 dBA if one sits 100 meters from US Hwy 271 and the other 500 meters away. The model captures this at 100-meter resolution, so noise exposure changes block by block.
Tree canopy can help reduce modeled noise exposure. Roughly 32% of Arthur City is under tree cover (about average for cities), and the dominant land cover is pasture / hay. Both are measured from federal USDA Forest Service and USGS satellite imagery at 30-meter resolution. Streets with 60% or higher canopy show 3 to 5 dBA lower noise than comparable streets with bare ground or pavement, which is why the per-place decay rate above already accounts for it.
Sources & Methodology
The BestNeighborhood noise model is calibrated against nearly one million federal ground-truth measurements across four states. Road noise is computed from segment-level federal traffic data and propagated outward using physics-based acoustic decay, with attenuation rates that depend on the surrounding land cover.
All inputs are published federal datasets. Block-level noise is computed by combining road, rail, and aviation sound sources in the energy domain, the same physics used in professional environmental noise assessments. Read the full methodology.
