This map shows modeled outdoor noise across Atlanta at 100-meter resolution, combining road, aviation, and rail sources. Green areas measure below 45 dBA. Orange and red exceed the EPA's 55 dBA outdoor threshold linked to long-term health effects. Use the layer toggles to view each source on its own or all together.
What the numbers sound like
- 30 dBAWhisper
- 40 dBASoft rainfall
- 45 dBAQuiet suburban street at night
- 50 dBAQuiet office
- 55 dBAEPA outdoor threshold: light traffic 100 ft away
- 60 dBANormal conversation an arm's length away
- 65 dBABusy restaurant
- 70 dBAHighway traffic 50 ft away
- 80 dBACity bus interior
Population Above the EPA Outdoor Threshold
The EPA's 55 dBA outdoor reference level is a common benchmark for residential noise exposure, especially for activity interference, annoyance, and long-term community noise concerns. About 315,095 Atlanta residents, or 49.6%, live above that level. By land area, 56.6% of Atlanta is above 55 dBA.
See how noise in Atlanta compares to similar-sized cities.
Noise by Part of Atlanta
Average noise levels for Atlanta residents, grouped by direction from the center of Atlanta. Central Atlanta carries the highest population-weighted average; Western Atlanta carries the lowest. Just 36% of residents in Western Atlanta live in blocks above the EPA's 55 dBA threshold, about two-thirds of the share in Central Atlanta.
Central Atlanta
68% of people above 55 dBA
Eastern Atlanta
56% of people above 55 dBA
Northern Atlanta
53% of people above 55 dBA
Southern Atlanta
50% of people above 55 dBA
Western Atlanta
36% of people above 55 dBA
Central Atlanta sounds about 49% louder than Western Atlanta to the human ear, a 5.8 dBA gap. Every 10 dBA roughly doubles perceived loudness. Within any of these directions, two homes a quarter mile apart can still differ by 10 or more dBA depending on how close they sit to a major highway.
Loudest Road Corridors
The model evaluates every road in Atlanta using federal traffic counts, posted speeds, heavy-truck ratios, and pavement type. The source level shown is the modeled noise at the road centerline, where it is loudest. Noise drops with distance, faster in vegetated areas and slower over open pavement.
How far back from State Rte 401 do you need to be?
State Rte 401 produces an estimated 83 dBA at its loudest centerline points. Noise drops logarithmically with distance, with the exact rate depending on what's between you and the road. Tree cover, walls, terrain, and pavement type all matter. At roughly a quarter mile back, traffic fades into the noise level of a quiet suburban street at night.
Calculated from the model's calibrated attenuation formula. About 38% of Atlanta sits under tree canopy (about average for cities) and roughly 38% is impervious surface like pavement and rooftops. Both are folded into the per-place decay rate above. Heavier canopy pulls noise down faster with distance; impervious surfaces slow the drop.
Rail Noise
Active freight rail runs through parts of Atlanta. For most blocks the rail-only contribution is small. Combined road-plus-rail noise rarely exceeds road noise on its own. The exceptions are the handful of blocks within roughly a quarter mile of the right-of-way during pass-through hours.
Use the Rail toggle on the map above to isolate rail's contribution from road and aviation.
Airport Noise
Hartsfield/Jackson Atlanta International (ATL) sits south of Atlanta. The U.S. Department of Transportation measures aviation noise around this airport directly, and the model uses those federal measurements rather than synthetic predictions.
Blocks under the approach and departure paths carry combined road-plus-aviation noise, with some exceeding 105 dBA on the map's Overall layer. Blocks on the opposite side of Atlanta, particularly to the north, show no measurable aviation contribution. Use the Aviation toggle on the map above to isolate the airport's footprint.
How Noise Is Distributed Across Atlanta
The bar chart below shows the share of Atlanta residents in each noise band. About 39% of residents live below the EPA's 55 dBA threshold, and roughly 24% live in blocks above 60 dBA. Long-term exposure in that range is linked to elevated stress hormones and cardiovascular risk.
How Atlanta Compares
Atlanta sits the highest among the peer group. Below: how Atlanta's average outdoor noise and share of residents above the EPA threshold compare with Marietta, Lawrenceville, Decatur, and Sandy Springs.
Average noise level (dBA)
Atlanta's 57.0 dBA pop-weighted average is the highest among the peer group. Georgia as a whole averages 51.0 dBA and the U.S. averages 52.0 dBA. Both are lower than Atlanta because most of either area is rural land away from major roads.
Share of residents above 55 dBA
About 49.6% of Atlanta residents live in blocks where outdoor levels exceed the EPA's 55 dBA threshold. That's more than any of its peer group. Measured by land area instead, 56.6% of Atlanta's footprint sits above 55 dBA, against a Georgia average of 22.6% and a national average of 28.1%.
What This Means if You're Moving to Atlanta
- Distance from highways matters more than the neighborhood name. Two homes in the same zip code can differ by 20 dBA if one sits 100 meters from State Rte 401 and the other 500 meters away. The model captures this at 100-meter resolution, so noise exposure changes block by block.
- Tree canopy can help reduce modeled noise exposure. Roughly 38% of Atlanta is under tree cover (about average for cities), and the dominant land cover is low-density developed open space. Both are measured from federal USDA Forest Service and USGS satellite imagery at 30-meter resolution. Streets with 60% or higher canopy show 3 to 5 dBA lower noise than comparable streets with bare ground or pavement, which is why the per-place decay rate above already accounts for it.
- Airport noise is directional. Hartsfield/Jackson Atlanta International's approach paths concentrate aviation noise to the south. Neighborhoods to the north of downtown show no measurable contribution from the airport.
Sources & Methodology
The BestNeighborhood noise model is calibrated against nearly one million federal ground-truth measurements across four states. Road noise is computed from segment-level federal traffic data and propagated outward using physics-based acoustic decay, with attenuation rates that depend on the surrounding land cover.
Federal datasets used:
FHWA Highway Performance Monitoring System: road geometry, traffic counts, lane configuration
U.S. DoT Bureau of Transportation Statistics National Transportation Noise Map: aviation and rail noise, road calibration ground truth
USGS / MRLC National Land Cover Database: land cover and impervious surface coverage
USDA Forest Service Tree Canopy Cover: vegetation density for sound propagation
U.S. Census Bureau TIGER/Line: block-level geography and population
U.S. EPA Levels Document: 55 dBA outdoor reference level
All inputs are published federal datasets. Block-level noise is computed by combining road, rail, and aviation sound sources in the energy domain, the same physics used in professional environmental noise assessments. Read the full methodology.