Noise Levels in Elmira, OR | Find Quiet Neighborhoods With Our Sound Map
46 dBA
Average noise across Elmira
Quiet suburban street at night
136
Residents above the EPA 55 dBA threshold
4% of Elmira residents
65 dBA
Loudest residential point
Busy restaurant
This map shows modeled outdoor noise across Elmira at 100-meter resolution, combining road, aviation, and rail sources. Green areas measure below 45 dBA. Orange and red exceed the EPA's 55 dBA outdoor threshold linked to long-term health effects. Use the layer toggles to view each source on its own or all together.
Overall
Road
Rail
Aviation
Click the map to explore
35 dBa55 dBa (EPA limit)90+ dBa
3545557090
Quietest (dBA)Loudest
Colorblind friendlyoff
What the numbers sound like
30 dBAWhisper
40 dBASoft rainfall
45 dBAQuiet suburban street at night
50 dBAQuiet office
55 dBAEPA outdoor threshold: light traffic 100 ft away
60 dBANormal conversation an arm's length away
65 dBABusy restaurant
70 dBAHighway traffic 50 ft away
80 dBACity bus interior
Population Above the EPA Outdoor Threshold
The EPA's 55 dBA outdoor reference level is a common benchmark for residential noise exposure, especially for activity interference, annoyance, and long-term community noise concerns. About 136 Elmira residents, or 4.4%, live above that level. By land area, 5.1% of Elmira is above 55 dBA.
Average noise levels for Elmira residents, grouped by direction from the center of Elmira. Southern Elmira carries the highest population-weighted average; Eastern Elmira carries the lowest. Just 2% of residents in Eastern Elmira live in blocks above the EPA's 55 dBA threshold, about half the share in Southern Elmira.
Eastern Elmira
42.6 dBA · Quiet
Quiet suburban street at night
2% of people above 55 dBA
QuietLoud
Northern Elmira
45.6 dBA · Mostly quiet
Quiet suburban street at night
5% of people above 55 dBA
QuietLoud
Southern Elmira
47.7 dBA · Mostly quiet
Quiet office
6% of people above 55 dBA
QuietLoud
Western Elmira
44.8 dBA · Quiet
Quiet suburban street at night
2% of people above 55 dBA
QuietLoud
Southern Elmira sounds about 42% louder than Eastern Elmira to the human ear, a 5.1 dBA gap. Every 10 dBA roughly doubles perceived loudness. Within any of these directions, two homes a quarter mile apart can still differ by 10 or more dBA depending on how close they sit to a major highway.
How far back from do you need to be?
produces an estimated 65 dBA at its loudest centerline points. Noise drops logarithmically with distance, with the exact rate depending on what's between you and the road. Tree cover, walls, terrain, and pavement type all matter. At roughly a quarter mile back, traffic fades into the noise level of a soft rainfall.
At source
65 dBA
Busy restaurant
165 ft
53 dBA
Quiet office to normal conversation
330 ft
46 dBA
Quiet suburban street at night
660 ft
39 dBA
Soft rainfall
¼ mile
35 dBA
Soft rainfall
½ mile
35 dBA
Soft rainfall
Calculated from the model's calibrated attenuation formula. About 41% of Elmira sits under tree canopy (heavier than most cities) and roughly 4% is impervious surface like pavement and rooftops. Both are folded into the per-place decay rate above. Heavier canopy pulls noise down faster with distance; impervious surfaces slow the drop.
-->
Airport Noise
Mahlon Sweet Field (EUG) sits east of Elmira. The U.S. Department of Transportation models aviation noise around this airport from federal traffic data, and the model uses those federal measurements rather than synthetic predictions.
Blocks under the approach and departure paths carry combined road-plus-aviation noise, with some exceeding 55 dBA on the map's Overall layer. Blocks on the opposite side of Elmira, particularly to the west, show no measurable aviation contribution. Use the Aviation toggle on the map above to isolate the airport's footprint.
How Noise Is Distributed Across Elmira
The bar chart below shows the share of Elmira residents in each noise band. About 100% of residents live below the EPA's 55 dBA threshold, and roughly 0% live in blocks above 60 dBA. Long-term exposure in that range is linked to elevated stress hormones and cardiovascular risk.
How Elmira Compares
Elmira sits at the quieter end of the spectrum. Below: how Elmira's average outdoor noise and share of residents above the EPA threshold compare with Monroe, Harrisburg, Pleasant Hill, and Cheshire.
Average noise level (dBA)
Elmira's 45.7 dBA pop-weighted average is at the quieter end of the spectrum. Oregon as a whole averages 52.9 dBA and the U.S. averages 52.0 dBA. Both are lower than Elmira because most of either area is rural land away from major roads.
Share of residents above 55 dBA
About 4.4% of Elmira residents live in blocks where outdoor levels exceed the EPA's 55 dBA threshold. That's fewer than any of its peer group. Measured by land area instead, 5.1% of Elmira's footprint sits above 55 dBA, against a Oregon average of 24.2% and a national average of 28.1%.
What This Means if You're Moving to Elmira
Distance from highways matters more than the neighborhood name. Two homes in the same zip code can differ by 20 dBA if one sits 100 meters from and the other 500 meters away. The model captures this at 100-meter resolution, so noise exposure changes block by block.
Tree canopy can help reduce modeled noise exposure. Roughly 41% of Elmira is under tree cover (heavier than most cities), and the dominant land cover is evergreen forest. Both are measured from federal USDA Forest Service and USGS satellite imagery at 30-meter resolution. Streets with 60% or higher canopy show 3 to 5 dBA lower noise than comparable streets with bare ground or pavement, which is why the per-place decay rate above already accounts for it.
Airport noise is directional. Mahlon Sweet Field's approach paths concentrate aviation noise to the east. Neighborhoods to the west of downtown show no measurable contribution from the airport.
Sources & Methodology
The BestNeighborhood noise model is calibrated against nearly one million federal ground-truth measurements across four states. Road noise is computed from segment-level federal traffic data and propagated outward using physics-based acoustic decay, with attenuation rates that depend on the surrounding land cover.
All inputs are published federal datasets. Block-level noise is computed by combining road, rail, and aviation sound sources in the energy domain, the same physics used in professional environmental noise assessments. Read the full methodology.
