Noise Levels in Hyde Park, UT | Find Quiet Neighborhoods With Our Sound Map
50 dBA
Average noise across Hyde Park
Quiet office
1,092
Residents above the EPA 55 dBA threshold
23% of Hyde Park residents
75 dBA
Loudest residential point
City bus interior
This map shows modeled outdoor noise across Hyde Park at 100-meter resolution, combining road, aviation, and rail sources. Green areas measure below 45 dBA. Orange and red exceed the EPA's 55 dBA outdoor threshold linked to long-term health effects. Use the layer toggles to view each source on its own or all together.
Overall
Road
Rail
Aviation
Click the map to explore
35 dBa55 dBa (EPA limit)90+ dBa
3545557090
Quietest (dBA)Loudest
Colorblind friendlyoff
What the numbers sound like
30 dBAWhisper
40 dBASoft rainfall
45 dBAQuiet suburban street at night
50 dBAQuiet office
55 dBAEPA outdoor threshold: light traffic 100 ft away
60 dBANormal conversation an arm's length away
65 dBABusy restaurant
70 dBAHighway traffic 50 ft away
80 dBACity bus interior
Population Above the EPA Outdoor Threshold
The EPA's 55 dBA outdoor reference level is a common benchmark for residential noise exposure, especially for activity interference, annoyance, and long-term community noise concerns. About 1,092 Hyde Park residents, or 22.6%, live above that level. By land area, 27.1% of Hyde Park is above 55 dBA.
Average noise levels for Hyde Park residents, grouped by direction from the center of Hyde Park. Central Hyde Park carries the highest population-weighted average; Eastern Hyde Park carries the lowest. Just 10% of residents in Eastern Hyde Park live in blocks above the EPA's 55 dBA threshold, a third of the share in Central Hyde Park.
Central Hyde Park
53.7 dBA · Moderate-loud
Quiet office to normal conversation
33% of people above 55 dBA
QuietLoud
Eastern Hyde Park
45.9 dBA · Mostly quiet
Quiet suburban street at night
10% of people above 55 dBA
QuietLoud
Northern Hyde Park
51.0 dBA · Moderate
Quiet office
26% of people above 55 dBA
QuietLoud
Southern Hyde Park
50.9 dBA · Moderate
Quiet office
28% of people above 55 dBA
QuietLoud
Western Hyde Park
52.3 dBA · Moderate
Quiet office to normal conversation
23% of people above 55 dBA
QuietLoud
Central Hyde Park sounds about 72% louder than Eastern Hyde Park to the human ear, a 7.8 dBA gap. Every 10 dBA roughly doubles perceived loudness. Within any of these directions, two homes a quarter mile apart can still differ by 10 or more dBA depending on how close they sit to a major highway.
How far back from Hwy 91 / Main St do you need to be?
Hwy 91 / Main St produces an estimated 68 dBA at its loudest centerline points. Noise drops logarithmically with distance, with the exact rate depending on what's between you and the road. Tree cover, walls, terrain, and pavement type all matter. At roughly a quarter mile back, traffic fades into the noise level of a soft rainfall.
At source
68 dBA
Highway traffic 50 ft away
165 ft
54 dBA
Quiet office to normal conversation
330 ft
46 dBA
Quiet office
660 ft
38 dBA
Soft rainfall
¼ mile
35 dBA
Soft rainfall
½ mile
35 dBA
Soft rainfall
Calculated from the model's calibrated attenuation formula. About 4% of Hyde Park sits under tree canopy (much lighter than most cities) and roughly 21% is impervious surface like pavement and rooftops. Both are folded into the per-place decay rate above. Heavier canopy pulls noise down faster with distance; impervious surfaces slow the drop.
-->
Rail Noise
Active freight rail runs through parts of Hyde Park. For most blocks the rail-only contribution is small. Combined road-plus-rail noise rarely exceeds road noise on its own. The exceptions are the handful of blocks within roughly a quarter mile of the right-of-way during pass-through hours.
Use the Rail toggle on the map above to isolate rail's contribution from road and aviation.
How Noise Is Distributed Across Hyde Park
The bar chart below shows the share of Hyde Park residents in each noise band. About 80% of residents live below the EPA's 55 dBA threshold, and roughly 0% live in blocks above 60 dBA. Long-term exposure in that range is linked to elevated stress hormones and cardiovascular risk.
How Hyde Park Compares
Hyde Park sits the highest among the peer group. Below: how Hyde Park's average outdoor noise and share of residents above the EPA threshold compare with Wellsville, Richmond, Providence, and Nibley.
Average noise level (dBA)
Hyde Park's 50.4 dBA pop-weighted average is the highest among the peer group. Utah as a whole averages 53.1 dBA and the U.S. averages 52.0 dBA. Both are lower than Hyde Park because most of either area is rural land away from major roads.
Share of residents above 55 dBA
About 22.6% of Hyde Park residents live in blocks where outdoor levels exceed the EPA's 55 dBA threshold. That's more than any of its peer group. Measured by land area instead, 27.1% of Hyde Park's footprint sits above 55 dBA, against a Utah average of 25.8% and a national average of 28.1%.
What This Means if You're Moving to Hyde Park
Distance from highways matters more than the neighborhood name. Two homes in the same zip code can differ by 20 dBA if one sits 100 meters from Hwy 91 / Main St and the other 500 meters away. The model captures this at 100-meter resolution, so noise exposure changes block by block.
Tree canopy can help reduce modeled noise exposure. Roughly 4% of Hyde Park is under tree cover (much lighter than most cities), and the dominant land cover is low-density developed open space. Both are measured from federal USDA Forest Service and USGS satellite imagery at 30-meter resolution. Streets with 60% or higher canopy show 3 to 5 dBA lower noise than comparable streets with bare ground or pavement, which is why the per-place decay rate above already accounts for it.
Sources & Methodology
The BestNeighborhood noise model is calibrated against nearly one million federal ground-truth measurements across four states. Road noise is computed from segment-level federal traffic data and propagated outward using physics-based acoustic decay, with attenuation rates that depend on the surrounding land cover.
All inputs are published federal datasets. Block-level noise is computed by combining road, rail, and aviation sound sources in the energy domain, the same physics used in professional environmental noise assessments. Read the full methodology.
