Noise Levels in Santa Fe, TX | Find Quiet Neighborhoods With Our Sound Map
49 dBA
Average noise across Santa Fe
Quiet office
3,106
Residents above the EPA 55 dBA threshold
15% of Santa Fe residents
84 dBA
Loudest residential point
Food blender at arm’s length
This map shows modeled outdoor noise across Santa Fe at 100-meter resolution, combining road, aviation, and rail sources. Green areas measure below 45 dBA. Orange and red exceed the EPA's 55 dBA outdoor threshold linked to long-term health effects. Use the layer toggles to view each source on its own or all together.
Overall
Road
Rail
Aviation
Click the map to explore
35 dBa55 dBa (EPA limit)90+ dBa
3545557090
Quietest (dBA)Loudest
Colorblind friendlyoff
What the numbers sound like
30 dBAWhisper
40 dBASoft rainfall
45 dBAQuiet suburban street at night
50 dBAQuiet office
55 dBAEPA outdoor threshold: light traffic 100 ft away
60 dBANormal conversation an arm's length away
65 dBABusy restaurant
70 dBAHighway traffic 50 ft away
80 dBACity bus interior
Population Above the EPA Outdoor Threshold
The EPA's 55 dBA outdoor reference level is a common benchmark for residential noise exposure, especially for activity interference, annoyance, and long-term community noise concerns. About 3,106 Santa Fe residents, or 15.0%, live above that level. By land area, 20.1% of Santa Fe is above 55 dBA.
Average noise levels for Santa Fe residents, grouped by direction from the center of Santa Fe. Central Santa Fe carries the highest population-weighted average; Southern Santa Fe carries the lowest. Just 7% of residents in Southern Santa Fe live in blocks above the EPA's 55 dBA threshold, a fifth of the share in Central Santa Fe.
Central Santa Fe
60.8 dBA · Loud
Normal conversation an arm’s length away
60% of people above 55 dBA
QuietLoud
Eastern Santa Fe
49.8 dBA · Mostly quiet
Quiet office
16% of people above 55 dBA
QuietLoud
Northern Santa Fe
49.3 dBA · Mostly quiet
Quiet office
16% of people above 55 dBA
QuietLoud
Southern Santa Fe
46.0 dBA · Mostly quiet
Quiet suburban street at night
7% of people above 55 dBA
QuietLoud
Western Santa Fe
48.6 dBA · Mostly quiet
Quiet office
15% of people above 55 dBA
QuietLoud
Central Santa Fe sounds about 179% louder than Southern Santa Fe to the human ear, a 14.8 dBA gap. Every 10 dBA roughly doubles perceived loudness. Within any of these directions, two homes a quarter mile apart can still differ by 10 or more dBA depending on how close they sit to a major highway.
How far back from do you need to be?
produces an estimated 84 dBA at its loudest centerline points. Noise drops logarithmically with distance, with the exact rate depending on what's between you and the road. Tree cover, walls, terrain, and pavement type all matter. At roughly a quarter mile back, traffic fades into the noise level of a quiet suburban street at night.
At source
84 dBA
Food blender at arm’s length
165 ft
70 dBA
Highway traffic 50 ft away
330 ft
62 dBA
Busy restaurant
660 ft
54 dBA
Quiet office to normal conversation
¼ mile
46 dBA
Quiet suburban street at night
½ mile
38 dBA
Soft rainfall
Calculated from the model's calibrated attenuation formula. About 10% of Santa Fe sits under tree canopy (lighter than most cities) and roughly 18% is impervious surface like pavement and rooftops. Both are folded into the per-place decay rate above. Heavier canopy pulls noise down faster with distance; impervious surfaces slow the drop.
-->
Rail Noise
Active freight rail runs through parts of Santa Fe. For most blocks the rail-only contribution is small. Combined road-plus-rail noise rarely exceeds road noise on its own. The exceptions are the handful of blocks within roughly a quarter mile of the right-of-way during pass-through hours.
Use the Rail toggle on the map above to isolate rail's contribution from road and aviation.
How Noise Is Distributed Across Santa Fe
The bar chart below shows the share of Santa Fe residents in each noise band. About 86% of residents live below the EPA's 55 dBA threshold, and roughly 8% live in blocks above 60 dBA. Long-term exposure in that range is linked to elevated stress hormones and cardiovascular risk.
How Santa Fe Compares
Santa Fe sits the lowest among the peer group. Below: how Santa Fe's average outdoor noise and share of residents above the EPA threshold compare with Dickinson, Texas City, Webster, and Galveston.
Average noise level (dBA)
Santa Fe's 48.7 dBA pop-weighted average is the lowest among the peer group. Texas as a whole averages 50.8 dBA and the U.S. averages 52.0 dBA. Both are lower than Santa Fe because most of either area is rural land away from major roads.
Share of residents above 55 dBA
About 15.0% of Santa Fe residents live in blocks where outdoor levels exceed the EPA's 55 dBA threshold. That's fewer than any of its peer group. Measured by land area instead, 20.1% of Santa Fe's footprint sits above 55 dBA, against a Texas average of 22.8% and a national average of 28.1%.
What This Means if You're Moving to Santa Fe
Distance from highways matters more than the neighborhood name. Two homes in the same zip code can differ by 20 dBA if one sits 100 meters from and the other 500 meters away. The model captures this at 100-meter resolution, so noise exposure changes block by block.
Tree canopy can help reduce modeled noise exposure. Roughly 10% of Santa Fe is under tree cover (lighter than most cities), and the dominant land cover is low-density developed open space. Both are measured from federal USDA Forest Service and USGS satellite imagery at 30-meter resolution. Streets with 60% or higher canopy show 3 to 5 dBA lower noise than comparable streets with bare ground or pavement, which is why the per-place decay rate above already accounts for it.
Sources & Methodology
The BestNeighborhood noise model is calibrated against nearly one million federal ground-truth measurements across four states. Road noise is computed from segment-level federal traffic data and propagated outward using physics-based acoustic decay, with attenuation rates that depend on the surrounding land cover.
All inputs are published federal datasets. Block-level noise is computed by combining road, rail, and aviation sound sources in the energy domain, the same physics used in professional environmental noise assessments. Read the full methodology.
