Noise Levels in Alton, TX | Find Quiet Neighborhoods With Our Sound Map
49 dBA
Average noise across Alton
Quiet office
1,398
Residents above the EPA 55 dBA threshold
11% of Alton residents
67 dBA
Loudest residential point
Highway traffic 50 ft away
This map shows modeled outdoor noise across Alton at 100-meter resolution, combining road, aviation, and rail sources. Green areas measure below 45 dBA. Orange and red exceed the EPA's 55 dBA outdoor threshold linked to long-term health effects. Use the layer toggles to view each source on its own or all together.
Overall
Road
Rail
Aviation
Click the map to explore
35 dBa55 dBa (EPA limit)90+ dBa
3545557090
Quietest (dBA)Loudest
Colorblind friendlyoff
What the numbers sound like
30 dBAWhisper
40 dBASoft rainfall
45 dBAQuiet suburban street at night
50 dBAQuiet office
55 dBAEPA outdoor threshold: light traffic 100 ft away
60 dBANormal conversation an arm's length away
65 dBABusy restaurant
70 dBAHighway traffic 50 ft away
80 dBACity bus interior
Population Above the EPA Outdoor Threshold
The EPA's 55 dBA outdoor reference level is a common benchmark for residential noise exposure, especially for activity interference, annoyance, and long-term community noise concerns. About 1,398 Alton residents, or 11.2%, live above that level. By land area, 20.7% of Alton is above 55 dBA.
Average noise levels for Alton residents, grouped by direction from the center of Alton. Western Alton carries the highest population-weighted average; Northern Alton carries the lowest. Just 13% of residents in Northern Alton live in blocks above the EPA's 55 dBA threshold, roughly the same as the share in Western Alton.
Central Alton
48.1 dBA · Mostly quiet
Quiet office
44% of people above 55 dBA
QuietLoud
Eastern Alton
47.9 dBA · Mostly quiet
Quiet office
10% of people above 55 dBA
QuietLoud
Northern Alton
47.1 dBA · Mostly quiet
Quiet office
13% of people above 55 dBA
QuietLoud
Southern Alton
47.3 dBA · Mostly quiet
Quiet office
10% of people above 55 dBA
QuietLoud
Western Alton
51.2 dBA · Moderate
Quiet office to normal conversation
11% of people above 55 dBA
QuietLoud
Western Alton sounds about 33% louder than Northern Alton to the human ear, a 4.1 dBA gap. Every 10 dBA roughly doubles perceived loudness. Within any of these directions, two homes a quarter mile apart can still differ by 10 or more dBA depending on how close they sit to a major highway.
How far back from do you need to be?
produces an estimated 67 dBA at its loudest centerline points. Noise drops logarithmically with distance, with the exact rate depending on what's between you and the road. Tree cover, walls, terrain, and pavement type all matter. At roughly a quarter mile back, traffic fades into the noise level of a soft rainfall.
At source
67 dBA
Highway traffic 50 ft away
165 ft
53 dBA
Quiet office to normal conversation
330 ft
45 dBA
Quiet suburban street at night
660 ft
37 dBA
Soft rainfall
¼ mile
35 dBA
Soft rainfall
½ mile
35 dBA
Soft rainfall
Calculated from the model's calibrated attenuation formula. About 1% of Alton sits under tree canopy (much lighter than most cities) and roughly 24% is impervious surface like pavement and rooftops. Both are folded into the per-place decay rate above. Heavier canopy pulls noise down faster with distance; impervious surfaces slow the drop.
-->
Airport Noise
Mcallen International (MFE) sits southeast of Alton. The U.S. Department of Transportation models aviation noise around this airport from federal traffic data, and the model uses those federal measurements rather than synthetic predictions.
Blocks under the approach and departure paths carry combined road-plus-aviation noise, with some exceeding 55 dBA on the map's Overall layer. Blocks on the opposite side of Alton, particularly to the northwest, show no measurable aviation contribution. Use the Aviation toggle on the map above to isolate the airport's footprint.
How Noise Is Distributed Across Alton
The bar chart below shows the share of Alton residents in each noise band. About 97% of residents live below the EPA's 55 dBA threshold, and roughly 0% live in blocks above 60 dBA. Long-term exposure in that range is linked to elevated stress hormones and cardiovascular risk.
How Alton Compares
Alton sits the lowest among the peer group. Below: how Alton's average outdoor noise and share of residents above the EPA threshold compare with Palmview, Penitas, Hidalgo, and Palmview South.
Average noise level (dBA)
Alton's 48.8 dBA pop-weighted average is the lowest among the peer group. Texas as a whole averages 50.8 dBA and the U.S. averages 52.0 dBA. Both are lower than Alton because most of either area is rural land away from major roads.
Share of residents above 55 dBA
About 11.2% of Alton residents live in blocks where outdoor levels exceed the EPA's 55 dBA threshold. That's fewer than any of its peer group. Measured by land area instead, 20.7% of Alton's footprint sits above 55 dBA, against a Texas average of 22.8% and a national average of 28.1%.
What This Means if You're Moving to Alton
Distance from highways matters more than the neighborhood name. Two homes in the same zip code can differ by 20 dBA if one sits 100 meters from and the other 500 meters away. The model captures this at 100-meter resolution, so noise exposure changes block by block.
Tree canopy can help reduce modeled noise exposure. Roughly 1% of Alton is under tree cover (much lighter than most cities), and the dominant land cover is low-intensity developed land. Both are measured from federal USDA Forest Service and USGS satellite imagery at 30-meter resolution. Streets with 60% or higher canopy show 3 to 5 dBA lower noise than comparable streets with bare ground or pavement, which is why the per-place decay rate above already accounts for it.
Airport noise is directional. Mcallen International's approach paths concentrate aviation noise to the southeast. Neighborhoods to the northwest of downtown show no measurable contribution from the airport.
Sources & Methodology
The BestNeighborhood noise model is calibrated against nearly one million federal ground-truth measurements across four states. Road noise is computed from segment-level federal traffic data and propagated outward using physics-based acoustic decay, with attenuation rates that depend on the surrounding land cover.
All inputs are published federal datasets. Block-level noise is computed by combining road, rail, and aviation sound sources in the energy domain, the same physics used in professional environmental noise assessments. Read the full methodology.
