This map shows modeled outdoor noise across Beaver Bay at 100-meter resolution, combining road, aviation, and rail sources. Green areas measure below 45 dBA. Orange and red exceed the EPA's 55 dBA outdoor threshold linked to long-term health effects. Use the layer toggles to view each source on its own or all together.
What the numbers sound like
- 30 dBAWhisper
- 40 dBASoft rainfall
- 45 dBAQuiet suburban street at night
- 50 dBAQuiet office
- 55 dBAEPA outdoor threshold: light traffic 100 ft away
- 60 dBANormal conversation an arm's length away
- 65 dBABusy restaurant
- 70 dBAHighway traffic 50 ft away
- 80 dBACity bus interior
Population Above the EPA Outdoor Threshold
The EPA's 55 dBA outdoor reference level is a common benchmark for residential noise exposure, especially for activity interference, annoyance, and long-term community noise concerns. About 53 Beaver Bay residents, or 29.1%, live above that level. By land area, 14.7% of Beaver Bay is above 55 dBA.
See how noise in Beaver Bay compares to similar-sized cities.
Noise by Part of Beaver Bay
Average noise levels for Beaver Bay residents, grouped by direction from the center of Beaver Bay. Southern Beaver Bay carries the highest population-weighted average; Western Beaver Bay carries the lowest. Just 0% of residents in Western Beaver Bay live in blocks above the EPA's 55 dBA threshold, a fifth of the share in Southern Beaver Bay.
Eastern Beaver Bay
38% of people above 55 dBA
Northern Beaver Bay
9% of people above 55 dBA
Southern Beaver Bay
33% of people above 55 dBA
Western Beaver Bay
0% of people above 55 dBA
Southern Beaver Bay sounds about 284% louder than Western Beaver Bay to the human ear, a 19.4 dBA gap. Every 10 dBA roughly doubles perceived loudness. Within any of these directions, two homes a quarter mile apart can still differ by 10 or more dBA depending on how close they sit to a major highway.
Loudest Road Corridors
The model evaluates every road in Beaver Bay using federal traffic counts, posted speeds, heavy-truck ratios, and pavement type. The source level shown is the modeled noise at the road centerline, where it is loudest. Noise drops with distance, faster in vegetated areas and slower over open pavement.
How far back from London Rd do you need to be?
London Rd produces an estimated 61 dBA at its loudest centerline points. Noise drops logarithmically with distance, with the exact rate depending on what's between you and the road. Tree cover, walls, terrain, and pavement type all matter. At roughly a quarter mile back, traffic fades into the noise level of a soft rainfall.
Calculated from the model's calibrated attenuation formula. About 54% of Beaver Bay sits under tree canopy (heavier than most cities) and roughly 7% is impervious surface like pavement and rooftops. Both are folded into the per-place decay rate above. Heavier canopy pulls noise down faster with distance; impervious surfaces slow the drop.
Rail Noise
Active freight rail runs through parts of Beaver Bay. For most blocks the rail-only contribution is small. Combined road-plus-rail noise rarely exceeds road noise on its own. The exceptions are the handful of blocks within roughly a quarter mile of the right-of-way during pass-through hours.
Use the Rail toggle on the map above to isolate rail's contribution from road and aviation.
How Noise Is Distributed Across Beaver Bay
The bar chart below shows the share of Beaver Bay residents in each noise band. About 63% of residents live below the EPA's 55 dBA threshold, and roughly 0% live in blocks above 60 dBA. Long-term exposure in that range is linked to elevated stress hormones and cardiovascular risk.
How Beaver Bay Compares
Beaver Bay sits the highest among the peer group. Below: how Beaver Bay's average outdoor noise and share of residents above the EPA threshold compare with Little Marais, East Beaver Bay, Wales, and Whyte.
Average noise level (dBA)
Beaver Bay's 50.9 dBA pop-weighted average is the highest among the peer group. Minnesota as a whole averages 53.6 dBA and the U.S. averages 52.0 dBA. Both are lower than Beaver Bay because most of either area is rural land away from major roads.
Share of residents above 55 dBA
About 29.1% of Beaver Bay residents live in blocks where outdoor levels exceed the EPA's 55 dBA threshold. That's more than any of its peer group. Measured by land area instead, 14.7% of Beaver Bay's footprint sits above 55 dBA, against a Minnesota average of 31.0% and a national average of 28.1%.
What This Means if You're Moving to Beaver Bay
- Distance from highways matters more than the neighborhood name. Two homes in the same zip code can differ by 20 dBA if one sits 100 meters from London Rd and the other 500 meters away. The model captures this at 100-meter resolution, so noise exposure changes block by block.
- Tree canopy can help reduce modeled noise exposure. Roughly 54% of Beaver Bay is under tree cover (heavier than most cities), and the dominant land cover is mixed forest. Both are measured from federal USDA Forest Service and USGS satellite imagery at 30-meter resolution. Streets with 60% or higher canopy show 3 to 5 dBA lower noise than comparable streets with bare ground or pavement, which is why the per-place decay rate above already accounts for it.
Sources & Methodology
The BestNeighborhood noise model is calibrated against nearly one million federal ground-truth measurements across four states. Road noise is computed from segment-level federal traffic data and propagated outward using physics-based acoustic decay, with attenuation rates that depend on the surrounding land cover.
Federal datasets used:
FHWA Highway Performance Monitoring System: road geometry, traffic counts, lane configuration
U.S. DoT Bureau of Transportation Statistics National Transportation Noise Map: aviation and rail noise, road calibration ground truth
USGS / MRLC National Land Cover Database: land cover and impervious surface coverage
USDA Forest Service Tree Canopy Cover: vegetation density for sound propagation
U.S. Census Bureau TIGER/Line: block-level geography and population
U.S. EPA Levels Document: 55 dBA outdoor reference level
All inputs are published federal datasets. Block-level noise is computed by combining road, rail, and aviation sound sources in the energy domain, the same physics used in professional environmental noise assessments. Read the full methodology.