Noise Levels in Litton, TN | Find Quiet Neighborhoods With Our Sound Map

33 dBA
Average noise across Litton
Whisper
0
Residents above the EPA 55 dBA threshold
0% of Litton residents
62 dBA
Loudest residential point
Busy restaurant

This map shows modeled outdoor noise across Litton at 100-meter resolution, combining road, aviation, and rail sources. Green areas measure below 45 dBA. Orange and red exceed the EPA's 55 dBA outdoor threshold linked to long-term health effects. Use the layer toggles to view each source on its own or all together.

Overall
Road
Rail
Aviation
Litton, TN Map of Noise Levels in Litton
Click the map to explore
35 45 55 70 90
Quietest (dBA) Loudest
Colorblind friendly off

What the numbers sound like

  • 30 dBAWhisper
  • 40 dBASoft rainfall
  • 45 dBAQuiet suburban street at night
  • 50 dBAQuiet office
  • 55 dBAEPA outdoor threshold: light traffic 100 ft away
  • 60 dBANormal conversation an arm's length away
  • 65 dBABusy restaurant
  • 70 dBAHighway traffic 50 ft away
  • 80 dBACity bus interior

Population Above the EPA Outdoor Threshold

The EPA's 55 dBA outdoor reference level is a common benchmark for residential noise exposure, especially for activity interference, annoyance, and long-term community noise concerns. About 0 Litton residents, or 0.1%, live above that level. By land area, 1.6% of Litton is above 55 dBA.

See how noise in Litton compares to similar-sized cities.

Noise by Part of Litton

Average noise levels for Litton residents, grouped by direction from the center of Litton. Central Litton carries the highest population-weighted average; Eastern Litton carries the lowest. Just 0% of residents in Eastern Litton live in blocks above the EPA's 55 dBA threshold, a fifth of the share in Central Litton.

Central Litton

42.9 dBA · Quiet
Quiet suburban street at night

2% of people above 55 dBA

QuietLoud

Eastern Litton

29.0 dBA · Quiet
Whisper

0% of people above 55 dBA

QuietLoud

Southern Litton

37.1 dBA · Quiet
Soft rainfall

0% of people above 55 dBA

QuietLoud

Western Litton

38.0 dBA · Quiet
Soft rainfall

0% of people above 55 dBA

QuietLoud

Central Litton sounds about 162% louder than Eastern Litton to the human ear, a 13.9 dBA gap. Every 10 dBA roughly doubles perceived loudness. Within any of these directions, two homes a quarter mile apart can still differ by 10 or more dBA depending on how close they sit to a major highway.

How far back from A157 do you need to be?

A157 produces an estimated 55 dBA at its loudest centerline points. Noise drops logarithmically with distance, with the exact rate depending on what's between you and the road. Tree cover, walls, terrain, and pavement type all matter. At roughly a quarter mile back, traffic fades into the noise level of a soft rainfall.

At source
55 dBA
Quiet office to normal conversation
165 ft
41 dBA
Soft rainfall
330 ft
35 dBA
Soft rainfall
660 ft
35 dBA
Soft rainfall
¼ mile
35 dBA
Soft rainfall
½ mile
35 dBA
Soft rainfall

Calculated from the model's calibrated attenuation formula. About 87% of Litton sits under tree canopy (much heavier than most cities) and roughly 0% is impervious surface like pavement and rooftops. Both are folded into the per-place decay rate above. Heavier canopy pulls noise down faster with distance; impervious surfaces slow the drop.

-->

How Noise Is Distributed Across Litton

The bar chart below shows the share of Litton residents in each noise band. About 100% of residents live below the EPA's 55 dBA threshold, and roughly 0% live in blocks above 60 dBA. Long-term exposure in that range is linked to elevated stress hormones and cardiovascular risk.

How Litton Compares

Litton sits at the quieter end of the spectrum. Below: how Litton's average outdoor noise and share of residents above the EPA threshold compare with Lorraine, Ogden, Dodson, and Eastland.

Average noise level (dBA)

Litton's 32.6 dBA pop-weighted average is at the quieter end of the spectrum. Tennessee as a whole averages 49.2 dBA and the U.S. averages 52.0 dBA. Both are lower than Litton because most of either area is rural land away from major roads.

Share of residents above 55 dBA

About 0.1% of Litton residents live in blocks where outdoor levels exceed the EPA's 55 dBA threshold. That's more than any of its peer group. Measured by land area instead, 1.6% of Litton's footprint sits above 55 dBA, against a Tennessee average of 18.7% and a national average of 28.1%.

What This Means if You're Moving to Litton

  • Distance from highways matters more than the neighborhood name. Two homes in the same zip code can differ by 20 dBA if one sits 100 meters from A157 and the other 500 meters away. The model captures this at 100-meter resolution, so noise exposure changes block by block.
  • Tree canopy can help reduce modeled noise exposure. Roughly 87% of Litton is under tree cover (much heavier than most cities), and the dominant land cover is deciduous forest. Both are measured from federal USDA Forest Service and USGS satellite imagery at 30-meter resolution. Streets with 60% or higher canopy show 3 to 5 dBA lower noise than comparable streets with bare ground or pavement, which is why the per-place decay rate above already accounts for it.

Sources & Methodology

The BestNeighborhood noise model is calibrated against nearly one million federal ground-truth measurements across four states. Road noise is computed from segment-level federal traffic data and propagated outward using physics-based acoustic decay, with attenuation rates that depend on the surrounding land cover.

Federal datasets used:

FHWA Highway Performance Monitoring System: road geometry, traffic counts, lane configuration
U.S. DoT Bureau of Transportation Statistics National Transportation Noise Map: aviation and rail noise, road calibration ground truth
USGS / MRLC National Land Cover Database: land cover and impervious surface coverage
USDA Forest Service Tree Canopy Cover: vegetation density for sound propagation
U.S. Census Bureau TIGER/Line: block-level geography and population
U.S. EPA Levels Document: 55 dBA outdoor reference level

All inputs are published federal datasets. Block-level noise is computed by combining road, rail, and aviation sound sources in the energy domain, the same physics used in professional environmental noise assessments. Read the full methodology.