Noise Levels in Mount Selman, TX | Find Quiet Neighborhoods With Our Sound Map

42 dBA
Average noise across Mount Selman
Quiet suburban street at night
19
Residents above the EPA 55 dBA threshold
2% of Mount Selman residents
69 dBA
Loudest residential point
Highway traffic 50 ft away

This map shows modeled outdoor noise across Mount Selman at 100-meter resolution, combining road, aviation, and rail sources. Green areas measure below 45 dBA. Orange and red exceed the EPA's 55 dBA outdoor threshold linked to long-term health effects. Use the layer toggles to view each source on its own or all together.

Overall
Road
Rail
Aviation
Mount Selman, TX Map of Noise Levels in Mount Selman
Click the map to explore
35 45 55 70 90
Quietest (dBA) Loudest
Colorblind friendly off

What the numbers sound like

  • 30 dBAWhisper
  • 40 dBASoft rainfall
  • 45 dBAQuiet suburban street at night
  • 50 dBAQuiet office
  • 55 dBAEPA outdoor threshold: light traffic 100 ft away
  • 60 dBANormal conversation an arm's length away
  • 65 dBABusy restaurant
  • 70 dBAHighway traffic 50 ft away
  • 80 dBACity bus interior

Population Above the EPA Outdoor Threshold

The EPA's 55 dBA outdoor reference level is a common benchmark for residential noise exposure, especially for activity interference, annoyance, and long-term community noise concerns. About 19 Mount Selman residents, or 1.8%, live above that level. By land area, 3.1% of Mount Selman is above 55 dBA.

See how noise in Mount Selman compares to similar-sized cities.

Noise by Part of Mount Selman

Average noise levels for Mount Selman residents, grouped by direction from the center of Mount Selman. Central Mount Selman carries the highest population-weighted average; Eastern Mount Selman carries the lowest. Just 0% of residents in Eastern Mount Selman live in blocks above the EPA's 55 dBA threshold, a fifth of the share in Central Mount Selman.

Central Mount Selman

50.1 dBA · Moderate
Quiet office

12% of people above 55 dBA

QuietLoud

Eastern Mount Selman

40.0 dBA · Quiet
Soft rainfall

0% of people above 55 dBA

QuietLoud

Northern Mount Selman

42.6 dBA · Quiet
Quiet suburban street at night

1% of people above 55 dBA

QuietLoud

Southern Mount Selman

42.1 dBA · Quiet
Quiet suburban street at night

3% of people above 55 dBA

QuietLoud

Western Mount Selman

40.2 dBA · Quiet
Soft rainfall

2% of people above 55 dBA

QuietLoud

Central Mount Selman sounds about 101% louder than Eastern Mount Selman to the human ear, a 10.1 dBA gap. Every 10 dBA roughly doubles perceived loudness. Within any of these directions, two homes a quarter mile apart can still differ by 10 or more dBA depending on how close they sit to a major highway.

How far back from do you need to be?

produces an estimated 69 dBA at its loudest centerline points. Noise drops logarithmically with distance, with the exact rate depending on what's between you and the road. Tree cover, walls, terrain, and pavement type all matter. At roughly a quarter mile back, traffic fades into the noise level of a soft rainfall.

At source
69 dBA
Highway traffic 50 ft away
165 ft
55 dBA
Quiet office to normal conversation
330 ft
46 dBA
Quiet office
660 ft
38 dBA
Soft rainfall
¼ mile
35 dBA
Soft rainfall
½ mile
35 dBA
Soft rainfall

Calculated from the model's calibrated attenuation formula. About 55% of Mount Selman sits under tree canopy (heavier than most cities) and roughly 0% is impervious surface like pavement and rooftops. Both are folded into the per-place decay rate above. Heavier canopy pulls noise down faster with distance; impervious surfaces slow the drop.

-->

How Noise Is Distributed Across Mount Selman

The bar chart below shows the share of Mount Selman residents in each noise band. About 96% of residents live below the EPA's 55 dBA threshold, and roughly 0% live in blocks above 60 dBA. Long-term exposure in that range is linked to elevated stress hormones and cardiovascular risk.

How Mount Selman Compares

Mount Selman sits at the louder end of the spectrum. Below: how Mount Selman's average outdoor noise and share of residents above the EPA threshold compare with Mixon, Tecula, Teaselville, and Shadybrook.

Average noise level (dBA)

Mount Selman's 41.6 dBA pop-weighted average is at the louder end of the spectrum. Texas as a whole averages 50.8 dBA and the U.S. averages 52.0 dBA. Both are lower than Mount Selman because most of either area is rural land away from major roads.

Share of residents above 55 dBA

About 1.8% of Mount Selman residents live in blocks where outdoor levels exceed the EPA's 55 dBA threshold. That's in the middle of its peer group. Measured by land area instead, 3.1% of Mount Selman's footprint sits above 55 dBA, against a Texas average of 22.8% and a national average of 28.1%.

What This Means if You're Moving to Mount Selman

  • Distance from highways matters more than the neighborhood name. Two homes in the same zip code can differ by 20 dBA if one sits 100 meters from and the other 500 meters away. The model captures this at 100-meter resolution, so noise exposure changes block by block.
  • Tree canopy can help reduce modeled noise exposure. Roughly 55% of Mount Selman is under tree cover (heavier than most cities), and the dominant land cover is mixed forest. Both are measured from federal USDA Forest Service and USGS satellite imagery at 30-meter resolution. Streets with 60% or higher canopy show 3 to 5 dBA lower noise than comparable streets with bare ground or pavement, which is why the per-place decay rate above already accounts for it.

Sources & Methodology

The BestNeighborhood noise model is calibrated against nearly one million federal ground-truth measurements across four states. Road noise is computed from segment-level federal traffic data and propagated outward using physics-based acoustic decay, with attenuation rates that depend on the surrounding land cover.

Federal datasets used:

FHWA Highway Performance Monitoring System: road geometry, traffic counts, lane configuration
U.S. DoT Bureau of Transportation Statistics National Transportation Noise Map: aviation and rail noise, road calibration ground truth
USGS / MRLC National Land Cover Database: land cover and impervious surface coverage
USDA Forest Service Tree Canopy Cover: vegetation density for sound propagation
U.S. Census Bureau TIGER/Line: block-level geography and population
U.S. EPA Levels Document: 55 dBA outdoor reference level

All inputs are published federal datasets. Block-level noise is computed by combining road, rail, and aviation sound sources in the energy domain, the same physics used in professional environmental noise assessments. Read the full methodology.