This map shows modeled outdoor noise across Colonial Heights at 100-meter resolution, combining road, aviation, and rail sources. Green areas measure below 45 dBA. Orange and red exceed the EPA's 55 dBA outdoor threshold linked to long-term health effects. Use the layer toggles to view each source on its own or all together.
What the numbers sound like
- 30 dBAWhisper
- 40 dBASoft rainfall
- 45 dBAQuiet suburban street at night
- 50 dBAQuiet office
- 55 dBAEPA outdoor threshold: light traffic 100 ft away
- 60 dBANormal conversation an arm's length away
- 65 dBABusy restaurant
- 70 dBAHighway traffic 50 ft away
- 80 dBACity bus interior
Population Above the EPA Outdoor Threshold
The EPA's 55 dBA outdoor reference level is a common benchmark for residential noise exposure, especially for activity interference, annoyance, and long-term community noise concerns. About 8,779 Colonial Heights residents, or 36.4%, live above that level. By land area, 48.2% of Colonial Heights is above 55 dBA.
See how noise in Colonial Heights compares to similar-sized cities.
Noise by Part of Colonial Heights
Average noise levels for Colonial Heights residents, grouped by direction from the center of Colonial Heights. Eastern Colonial Heights carries the highest population-weighted average; Central Colonial Heights carries the lowest. Just 0% of residents in Central Colonial Heights live in blocks above the EPA's 55 dBA threshold, a fifth of the share in Eastern Colonial Heights.
Central Colonial Heights
0% of people above 55 dBA
Eastern Colonial Heights
40% of people above 55 dBA
Northern Colonial Heights
19% of people above 55 dBA
Southern Colonial Heights
49% of people above 55 dBA
Western Colonial Heights
35% of people above 55 dBA
Eastern Colonial Heights sounds about 59% louder than Central Colonial Heights to the human ear, a 6.7 dBA gap. Every 10 dBA roughly doubles perceived loudness. Within any of these directions, two homes a quarter mile apart can still differ by 10 or more dBA depending on how close they sit to a major highway.
Loudest Road Corridors
The model evaluates every road in Colonial Heights using federal traffic counts, posted speeds, heavy-truck ratios, and pavement type. The source level shown is the modeled noise at the road centerline, where it is loudest. Noise drops with distance, faster in vegetated areas and slower over open pavement.
How far back from Richmond-petersburg Tpke do you need to be?
Richmond-petersburg Tpke produces an estimated 78 dBA at its loudest centerline points. Noise drops logarithmically with distance, with the exact rate depending on what's between you and the road. Tree cover, walls, terrain, and pavement type all matter. At roughly a quarter mile back, traffic fades into the noise level of a quiet suburban street at night.
Calculated from the model's calibrated attenuation formula. About 38% of Colonial Heights sits under tree canopy (about average for cities) and roughly 31% is impervious surface like pavement and rooftops. Both are folded into the per-place decay rate above. Heavier canopy pulls noise down faster with distance; impervious surfaces slow the drop.
Rail Noise
Active freight rail runs through parts of Colonial Heights. For most blocks the rail-only contribution is small. Combined road-plus-rail noise rarely exceeds road noise on its own. The exceptions are the handful of blocks within roughly a quarter mile of the right-of-way during pass-through hours.
Use the Rail toggle on the map above to isolate rail's contribution from road and aviation.
Airport Noise
Richmond International (RIC) sits north of Colonial Heights. The U.S. Department of Transportation models aviation noise around this airport from federal traffic data, and the model uses those federal measurements rather than synthetic predictions.
Blocks under the approach and departure paths carry combined road-plus-aviation noise, with some exceeding 65 dBA on the map's Overall layer. Blocks on the opposite side of Colonial Heights, particularly to the south, show no measurable aviation contribution. Use the Aviation toggle on the map above to isolate the airport's footprint.
How Noise Is Distributed Across Colonial Heights
The bar chart below shows the share of Colonial Heights residents in each noise band. About 53% of residents live below the EPA's 55 dBA threshold, and roughly 23% live in blocks above 60 dBA. Long-term exposure in that range is linked to elevated stress hormones and cardiovascular risk.
How Colonial Heights Compares
Colonial Heights sits the highest among the peer group. Below: how Colonial Heights's average outdoor noise and share of residents above the EPA threshold compare with Hopewell, Montrose Heights, Meadowbrook, and Chester.
Average noise level (dBA)
Colonial Heights's 55.9 dBA pop-weighted average is the highest among the peer group. Virginia as a whole averages 52.8 dBA and the U.S. averages 52.0 dBA. Both are lower than Colonial Heights because most of either area is rural land away from major roads.
Share of residents above 55 dBA
About 36.4% of Colonial Heights residents live in blocks where outdoor levels exceed the EPA's 55 dBA threshold. That's in the middle of its peer group. Measured by land area instead, 48.2% of Colonial Heights's footprint sits above 55 dBA, against a Virginia average of 30.0% and a national average of 28.1%.
What This Means if You're Moving to Colonial Heights
- Distance from highways matters more than the neighborhood name. Two homes in the same zip code can differ by 20 dBA if one sits 100 meters from Richmond-petersburg Tpke and the other 500 meters away. The model captures this at 100-meter resolution, so noise exposure changes block by block.
- Tree canopy can help reduce modeled noise exposure. Roughly 38% of Colonial Heights is under tree cover (about average for cities), and the dominant land cover is low-intensity developed land. Both are measured from federal USDA Forest Service and USGS satellite imagery at 30-meter resolution. Streets with 60% or higher canopy show 3 to 5 dBA lower noise than comparable streets with bare ground or pavement, which is why the per-place decay rate above already accounts for it.
- Airport noise is directional. Richmond International's approach paths concentrate aviation noise to the north. Neighborhoods to the south of downtown show no measurable contribution from the airport.
Sources & Methodology
The BestNeighborhood noise model is calibrated against nearly one million federal ground-truth measurements across four states. Road noise is computed from segment-level federal traffic data and propagated outward using physics-based acoustic decay, with attenuation rates that depend on the surrounding land cover.
Federal datasets used:
FHWA Highway Performance Monitoring System: road geometry, traffic counts, lane configuration
U.S. DoT Bureau of Transportation Statistics National Transportation Noise Map: aviation and rail noise, road calibration ground truth
USGS / MRLC National Land Cover Database: land cover and impervious surface coverage
USDA Forest Service Tree Canopy Cover: vegetation density for sound propagation
U.S. Census Bureau TIGER/Line: block-level geography and population
U.S. EPA Levels Document: 55 dBA outdoor reference level
All inputs are published federal datasets. Block-level noise is computed by combining road, rail, and aviation sound sources in the energy domain, the same physics used in professional environmental noise assessments. Read the full methodology.