This map shows modeled outdoor noise across Howard County at 100-meter resolution, combining road, aviation, and rail sources. Green areas measure below 45 dBA. Orange and red exceed the EPA's 55 dBA outdoor threshold linked to long-term health effects. Use the layer toggles to view each source on its own or all together.
What the numbers sound like
- 30 dBAWhisper
- 40 dBASoft rainfall
- 45 dBAQuiet suburban street at night
- 50 dBAQuiet office
- 55 dBAEPA outdoor threshold: light traffic 100 ft away
- 60 dBANormal conversation an arm's length away
- 65 dBABusy restaurant
- 70 dBAHighway traffic 50 ft away
- 80 dBACity bus interior
Population Above the EPA Outdoor Threshold
The EPA's 55 dBA outdoor reference level is a common benchmark for residential noise exposure, especially for activity interference, annoyance, and long-term community noise concerns. About 84,578 Howard County residents, or 27.0%, live above that level. By land area, 34.2% of Howard County is above 55 dBA.
See how noise in Howard County compares to similar-sized counties.
Noise by Part of Howard County
Average noise levels for Howard County residents, grouped by direction from the center of Howard County. The highest population-weighted average is in central Howard County; the lowest is in the Clarksville and Dayton areas (western Howard County), where just 16% of residents live in blocks above the EPA's 55 dBA threshold, about half the share in the loudest section.
Central Howard County
34% of people above 55 dBA
Jessup
44% of people above 55 dBA
Northeastern Howard County
29% of people above 55 dBA
Woodbine, West Friendship & Mount Airy
10% of people above 55 dBA
Clarksville & Dayton
16% of people above 55 dBA
To the human ear, noise in central Howard County sounds about 125% louder than in the Clarksville and Dayton areas (western Howard County), a 11.7 dBA gap. Every 10 dBA roughly doubles perceived loudness. Within any of these directions, two homes a quarter mile apart can still differ by 10 or more dBA depending on how close they sit to a major highway.
Loudest Road Corridors
The model evaluates every road in Howard County using federal traffic counts, posted speeds, heavy-truck ratios, and pavement type. The source level shown is the modeled noise at the road centerline, where it is loudest. Noise drops with distance from there.
How far back from State Hwy 100 do you need to be?
State Hwy 100 produces an estimated 79 dBA at its loudest centerline points. Noise drops logarithmically with distance, with the exact rate depending on what's between you and the road. Tree cover, walls, terrain, and pavement type all matter. At roughly a quarter mile back, traffic fades into the noise level of a quiet suburban street at night.
Calculated from the model's distance-decay formula. Where federal land-cover data reaches, the decay rate is set from the place's tree canopy, pavement and land cover. The map above uses one standard rate everywhere.
Rail Noise
Rail lines run through or near parts of Howard County. The U.S. Department of Transportation's National Transportation Noise Map models their noise, and the figures on this page add it to road and aviation noise.
Use the Rail toggle on the map above to isolate rail's contribution from road and aviation.
Airport Noise
Baltimore/Washington International Thurgood Marshall (BWI), a commercial airport, lies east of the center of Howard County. Use the Aviation toggle on the map above to see where its modeled noise reaches.
Aviation noise on the map comes from the U.S. Department of Transportation's National Transportation Noise Map, which models noise around the airports it covers. For airports outside that map, BestNeighborhood estimates noise from FAA traffic counts and runway layout, and keeps that estimate on the low side.
How Noise Is Distributed Across Howard County
The bar chart below shows the share of Howard County residents in each noise band. About 65% of residents live below the EPA's 55 dBA threshold, and roughly 14% live in blocks above 60 dBA. A systematic review for the World Health Organization's 2018 Environmental Noise Guidelines found that the risk of ischemic heart disease rises about 8% for every 10 dB increase in long-term road traffic noise.
How Howard County Compares
Howard County sits at the louder end of the spectrum. Below: how Howard County's average outdoor noise and share of residents above the EPA threshold compare with Baltimore City, Anne Arundel County, Frederick County, and Carroll County.
Average noise level (dBA)
Howard County's 53.6 dBA pop-weighted average is at the louder end of the spectrum. Maryland as a whole averages 52.3 dBA, and the U.S. averages 52.0 dBA.
Share of residents above 55 dBA
About 27.0% of Howard County residents live in blocks where outdoor levels exceed the EPA's 55 dBA threshold. That's in the middle of its peer group. Measured by land area instead, 34.2% of Howard County's footprint sits above 55 dBA, against a Maryland average of 32.9% and a national average of 28.1%.
What This Means if You're Moving to Howard County
- Distance from major roads matters more than the neighborhood name. Two homes in the same ZIP code can differ by more than 15 dBA when one sits 100 meters from a highway and the other 500 meters away. The model works at 100-meter resolution, so noise exposure changes block by block.
- Land cover sets how fast noise fades in the model. About 44% of Howard County is under tree canopy, heavier than most counties, and about 25% is impervious surface such as pavement and rooftops. Its most common land cover is low-density developed open space. These figures come from USDA Forest Service and USGS satellite data at 30-meter resolution, and the model uses them to set the rate at which noise fades with distance in Howard County.
- Airport noise follows the flight paths. Aviation noise concentrates under Baltimore/Washington International Thurgood Marshall's approach and departure paths, so two homes the same distance from its runways can hear different levels. The Aviation layer on the map shows its modeled footprint.
Sources & Methodology
The BestNeighborhood noise model is calibrated against nearly one million federal ground-truth measurements across four states. Road noise is computed from segment-level federal traffic data and propagated outward using physics-based acoustic decay, with attenuation rates that depend on the surrounding land cover.
Federal datasets used:
FHWA Highway Performance Monitoring System: road geometry, traffic counts, lane configuration
U.S. DoT Bureau of Transportation Statistics National Transportation Noise Map: aviation and rail noise, road calibration ground truth
USGS / MRLC National Land Cover Database: land cover and impervious surface coverage
USDA Forest Service Tree Canopy Cover: vegetation density for sound propagation
U.S. Census Bureau TIGER/Line: block-level geography and population
U.S. EPA Levels Document: 55 dBA outdoor reference level
Health research cited:
World Health Organization Environmental Noise Guidelines systematic review (2018): road traffic noise and heart disease
All inputs are published federal datasets. Block-level noise is computed by combining road, rail, and aviation sound sources in the energy domain, the same physics used in professional environmental noise assessments. Read the full methodology.