This map shows modeled outdoor noise across Talbot County at 100-meter resolution, combining road, aviation, and rail sources. Green areas measure below 45 dBA. Orange and red exceed the EPA's 55 dBA outdoor threshold linked to long-term health effects. Use the layer toggles to view each source on its own or all together.
What the numbers sound like
- 30 dBAWhisper
- 40 dBASoft rainfall
- 45 dBAQuiet suburban street at night
- 50 dBAQuiet office
- 55 dBAEPA outdoor threshold: light traffic 100 ft away
- 60 dBANormal conversation an arm's length away
- 65 dBABusy restaurant
- 70 dBAHighway traffic 50 ft away
- 80 dBACity bus interior
Population Above the EPA Outdoor Threshold
The EPA's 55 dBA outdoor reference level is a common benchmark for residential noise exposure, especially for activity interference, annoyance, and long-term community noise concerns. About 5,808 Talbot County residents, or 17.2%, live above that level. By land area, 23.1% of Talbot County is above 55 dBA.
See how noise in Talbot County compares to similar-sized counties.
Noise by Part of Talbot County
Average noise levels for Talbot County residents, grouped by direction from the center of Talbot County. The highest population-weighted average is in the Easton area (eastern Talbot County); the lowest is in northwestern Talbot County, where just 2% of residents live in blocks above the EPA's 55 dBA threshold, a fifth of the share in the loudest section.
Easton
26% of people above 55 dBA
Northeastern Talbot County
17% of people above 55 dBA
Trappe
4% of people above 55 dBA
Central Talbot County
2% of people above 55 dBA
Northwestern Talbot County
2% of people above 55 dBA
To the human ear, noise in the Easton area (eastern Talbot County) sounds about 96% louder than in northwestern Talbot County, a 9.7 dBA gap. Every 10 dBA roughly doubles perceived loudness. Within any of these directions, two homes a quarter mile apart can still differ by 10 or more dBA depending on how close they sit to a major highway.
How Noise Is Distributed Across Talbot County
The bar chart below shows the share of Talbot County residents in each noise band. About 83% of residents live below the EPA's 55 dBA threshold, and roughly 2% live in blocks above 60 dBA. Long-term exposure in that range is linked to elevated stress hormones and cardiovascular risk.
How Talbot County Compares
Talbot County sits the highest among the peer group. Below: how Talbot County's average outdoor noise and share of residents above the EPA threshold compare with Dorchester County, Caroline County, Queen Anne's County, and Kent County.
Average noise level (dBA)
Talbot County's 48.8 dBA pop-weighted average is the highest among the peer group. Maryland as a whole averages 52.3 dBA and the U.S. averages 52.0 dBA. Both are lower than Talbot County because most of either area is rural land away from major roads.
Share of residents above 55 dBA
About 17.2% of Talbot County residents live in blocks where outdoor levels exceed the EPA's 55 dBA threshold. That's more than any of its peer group. Measured by land area instead, 23.1% of Talbot County's footprint sits above 55 dBA, against a Maryland average of 32.9% and a national average of 28.1%.
What This Means if You're Moving to Talbot County
- Distance from highways matters more than the neighborhood name. Two homes in the same zip code can differ by 20 dBA if one sits 100 meters from and the other 500 meters away. The model captures this at 100-meter resolution, so noise exposure changes block by block.
- Tree canopy can help reduce modeled noise exposure. Roughly 34% of Talbot County is under tree cover (heavier than most counties), and the dominant land cover is cultivated cropland. Both are measured from federal USDA Forest Service and USGS satellite imagery at 30-meter resolution. Streets with 60% or higher canopy show 3 to 5 dBA lower noise than comparable streets with bare ground or pavement, which is why the per-place decay rate above already accounts for it.
Sources & Methodology
The BestNeighborhood noise model is calibrated against nearly one million federal ground-truth measurements across four states. Road noise is computed from segment-level federal traffic data and propagated outward using physics-based acoustic decay, with attenuation rates that depend on the surrounding land cover.
Federal datasets used:
FHWA Highway Performance Monitoring System: road geometry, traffic counts, lane configuration
U.S. DoT Bureau of Transportation Statistics National Transportation Noise Map: aviation and rail noise, road calibration ground truth
USGS / MRLC National Land Cover Database: land cover and impervious surface coverage
USDA Forest Service Tree Canopy Cover: vegetation density for sound propagation
U.S. Census Bureau TIGER/Line: block-level geography and population
U.S. EPA Levels Document: 55 dBA outdoor reference level
All inputs are published federal datasets. Block-level noise is computed by combining road, rail, and aviation sound sources in the energy domain, the same physics used in professional environmental noise assessments. Read the full methodology.